Saturday, November 21, 2026Sat, Nov 21 Updated

Trucking and freight news for drivers, carriers and shippers.

How to Slide Tandems and the Fifth Wheel to Balance Axle Weights

Slide trailer tandems to move weight between drives and trailer axles, and the fifth wheel to move it between steer and drives. Steps, limits and mistakes.

Red Coca-Cola truck parked outdoors on city street.
Photo: fabianoshow4 / Pexels

To balance axle weights on a tractor-trailer, slide the trailer tandems to shift weight between the drive axles and the trailer axles, and slide the fifth wheel to shift weight between the steer axle and the drive axles. Under federal limits, a typical five-axle rig must stay at or below 34,000 pounds (15,422 kg) on each tandem group and 80,000 pounds (36,287 kg) gross. Weigh the truck on a certified scale, make one adjustment at a time, and reweigh until every axle group is legal.

Which way does the weight move when you slide the tandems?

Moving the trailer tandems forward puts more weight on the trailer axles and takes weight off the drive axles. Moving them rearward does the opposite and loads the drives more. The tandems pick up weight as they get closer to the center of the load.

A common rule of thumb is about 250 pounds (113 kg) per hole on trailers with holes spaced roughly 6 inches (15 cm) apart. The real figure depends on the trailer, the load and where the freight sits, so treat it as a starting estimate and confirm it on the scale.

Which way does the weight move when you slide the fifth wheel?

Sliding the fifth wheel forward moves weight onto the steer axle and off the drives. Sliding it back moves weight off the steer axle and onto the drives. The fifth wheel controls how the kingpin load splits between the front of the tractor and the drive axles. It does not change what the trailer tandems carry.

Steer axle weight is usually limited by the axle and tire ratings on the tractor, not only by state law. Check the ratings on the door-jamb label and the tire sidewalls before you push weight forward. An overloaded steer axle wears tires fast and makes the truck harder to control in a hard stop.

How do you slide trailer tandems step by step?

  1. Park on level, solid ground with plenty of room ahead and behind, and make sure nobody is standing near the trailer.
  2. Set the trailer brakes by pulling the trailer air supply valve, and leave the tractor brakes released.
  3. Pull the release handle or flip the air switch on the slider so the locking pins retract. On manual sliders, the handle often needs a little rocking of the truck to come free.
  4. Check by eye that all locking pins are out of the holes.
  5. Ease the tractor forward to move the tandems rearward on the trailer, or back up to move them forward. Go slowly and stop as soon as you reach the hole you want.
  6. Push the release handle back in or reset the air switch so the pins drop.
  7. Walk back and confirm that every pin is fully seated through the rail. Then do a tug test: release the trailer brakes, set them again and gently pull against them to make sure the slider does not move.
  8. Reweigh before driving on.

A slider that is not locked can let the trailer box slide on the axles under braking, which can damage the trailer and cause a loss of control. Never skip the visual pin check.

How do you slide the fifth wheel step by step?

  1. Stay on level ground with the trailer coupled and the landing gear raised.
  2. Unlock the fifth wheel slider with the cab switch or the release handle on the slide plate.
  3. Set the trailer brakes and release the tractor brakes.
  4. Back up slightly to move the fifth wheel forward on the frame, or pull forward slightly to move it rearward.
  5. Lock the slider, then confirm that the locking plungers are engaged and the slider cannot move.
  6. Reweigh.

Leave enough room between the back of the cab and the trailer nose for turning, and keep the trailer’s landing gear and front corners clear of the drive tires and mud flaps. Moving the fifth wheel too far forward can make the trailer hit the cab in a tight turn.

What weight limits do you need to hit?

Federal rules for the Interstate system set 20,000 pounds (9,072 kg) on a single axle, 34,000 pounds on a tandem axle group and 80,000 pounds gross, subject to the bridge formula. The bridge formula ties allowed weight to the number of axles and the distance between them. The Federal Highway Administration explains it on its FHWA Freight Management and Operations size and weight pages, and our guide to truck weight limits and the bridge formula walks through the numbers.

States add their own rules. California, for example, limits the distance from the kingpin to the center of the rearmost trailer axle on most 53-foot trailers to 40 feet (12.2 m), so the tandems often have to sit far back there. Some states mark the required position on the trailer or check it at scales. Know the rule for every state on your route before you pick a hole.

What are the most common mistakes?

  • Sliding without weighing first, then guessing. Always get a scale ticket before and after.
  • Fixing gross weight by sliding. If the gross is over 80,000 pounds, no amount of sliding will make the load legal. The freight has to be reduced or reloaded.
  • Balancing the axles but breaking a kingpin-to-axle or length rule along the way.
  • Forgetting fuel. A full set of tanks adds weight to the steer and drive axles, and burning fuel removes it during the trip. Diesel weighs about 7 pounds per gallon (0.84 kg per liter).
  • Not locking the pins fully, or not checking them after a slide.
  • Sliding tandems with a badly placed load. If heavy freight is stacked at one end, the shipper may need to restack it.

Fuel planning matters on heavy loads. When you are close to the limit on the drives, fueling to full before the scale can push you over, so many drivers fuel with weigh stations on the route in mind.

Quick answers

Should I move the tandems or the fifth wheel first?

Start with whichever group is over. If the drives and trailer tandems are out of balance, slide the tandems. If the steer axle is light or heavy, adjust the fifth wheel. Changing the tandems also changes the kingpin load slightly, so recheck the steer axle afterward.

Can I slide the tandems with a loaded trailer?

Yes. Tandems are usually slid with the trailer loaded, since that is when axle weights matter. Go slowly, keep the trailer brakes set, and never slide on a slope.

Does a lighter truck class follow the same rules?

Smaller trucks have different weight ratings and rules. Our explainer on truck classes and GVWR shows which weights trigger which requirements.

Where can I find federal guidance on weights and safety rules?

Federal size and weight rules come from FHWA, and safety rules for commercial drivers come from the Federal Motor Carrier Safety Administration. State transportation departments publish their own axle, length and kingpin rules.

Prepared by TenFour News with AI-assisted drafting and automated fact checks — see our editorial policy. Spotted an error? Tell us.