Shipper Load and Count (SLC) on a Bill of Lading: Claims Impact
SLC on a bill of lading means the shipper loaded and counted the freight, so the driver is not vouching for the count. Here is how it changes cargo claims.

Shipper load and count (SLC) is a notation on a bill of lading that says the shipper loaded the trailer and counted the freight, and the carrier did not check either one. A driver who signs a bill of lading marked SLC is confirming that the seal and the freight were handed over, not that the piece count or the contents are right. The notation matters most when a receiver reports a shortage or damage, because it changes who has to prove what.
What does SLC mean on a bill of lading?
SLC means the shipper took responsibility for loading the freight and for stating how many pieces, pallets or cartons are on board. You will also see it written as “shipper’s load and count” or “SL&C,” and sometimes next to “said to contain” (STC), which tells the reader that the description of the contents comes from the shipper.
The bill of lading is the contract of carriage and the receipt for the freight. When the carrier loads and counts the shipment itself, the receipt carries more weight. When the shipper does it, the carrier is signing for a closed box it has not opened. For the basics of the document itself, see this explainer on the bill of lading and why drivers sign it.
When does a shipment get marked SLC?
SLC is normal on full truckload moves where the shipper loads at its own dock, the doors are closed and a seal goes on. The driver is often in the cab or the driver lounge while the dock crew loads, so nobody from the carrier sees the count.
It is also common on loads the driver is not allowed to watch for safety or site rules, on live loads where the facility keeps drivers out of the dock area, and on sealed trailers that are dropped and picked up later. On less-than-truckload freight the carrier usually handles and counts the pieces at the dock, so SLC is rarer there.
How does SLC change a cargo claim?
Under the Carmack Amendment, a shipper who files a claim for loss or damage in interstate trucking starts with a strong position: if the freight was delivered to the carrier in good condition and arrived damaged or short, the carrier is presumed liable unless it can show an accepted defense. The bill of lading is the main evidence that the freight was in good order and in the stated quantity when it was picked up.
SLC weakens that evidence for quantity. A carrier can point to the notation and argue that it never verified the count, so the shipper has to show with its own records (pick tickets, packing lists, load photos, dock logs) that the stated number of pieces really went on the truck. Without those records, a shortage claim on an SLC load is hard to win.
SLC does not erase the carrier’s duty to deliver what it took. If the seal was intact at pickup and broken or different at delivery, or if the freight was visibly damaged in transit, the carrier can still be held responsible. The notation covers what the carrier could not see, not what happened on the road.
What should a driver do before signing an SLC bill of lading?
Look at what you can see, and write down what you cannot confirm. These steps protect you and your carrier:
- Check that the bill of lading shows the pickup address, consignee, piece count, commodity description and any seal number.
- Confirm that SLC or “shipper load and count” is printed or written on the document if the shipper loaded the trailer.
- Photograph the load before the doors close if the facility allows it: pallet placement, strapping, visible damage and the inside of the trailer.
- Write exceptions on the bill of lading before signing, such as “pallet leaning,” “wet cartons,” “two pallets shrink-wrap torn” or “unable to verify count.”
- Record the seal number, take a photo of the seal on the door, and keep a copy of every page you signed.
Do not sign a clean bill of lading on freight you could see was damaged or poorly loaded. An unmarked document tells a claims adjuster the freight was in good order. For securement on the road, see the rules on tiedowns, working load limits and checks.
What should a carrier or owner-operator do when a shortage claim arrives?
Start by pulling the bill of lading, the seal records, the photos and the delivery receipt. Compare the piece count at delivery with the count on the bill of lading. Then compare the seal number on the delivery paperwork with the one recorded at pickup.
Under federal claims rules, a carrier that receives a written claim must acknowledge it in writing within 30 days and must pay, decline or make a settlement offer within 120 days, or tell the claimant in writing why it needs more time. The standard bill of lading terms also give the shipper nine months from delivery to file a claim in writing. The rules are in 49 CFR Part 370, and the Federal Motor Carrier Safety Administration is the agency that points carriers to them.
If the load was SLC and the seal was intact at delivery, tell the claimant that the carrier did not count the freight at pickup and ask for the shipper’s loading records. If the seal was broken, missing or different, expect the claim to be harder to deny, and bring in the carrier’s insurer early.
Does SLC protect against theft claims?
SLC helps with count disputes, not with theft that happens while the carrier has the freight. If a sealed trailer was broken into on a parking lot, the carrier is generally still responsible for the cargo, and the claim turns on the seal, the circumstances and the carrier’s insurance terms. Theft patterns are covered in recent reporting on cargo theft losses in the second quarter.
Quick answers
Can a driver refuse to sign an SLC bill of lading?
A driver can ask the dispatcher or carrier to resolve a disagreement before signing, but refusing outright can delay the load and may breach the carrier’s agreement with the broker or shipper. Writing exceptions on the document is the usual way to protect the carrier.
Is SLC the same as a sealed trailer?
No. A seal records that the doors were closed at a point in time and with which number. SLC records who loaded and counted. A load can be SLC with a seal, SLC without one, or counted by the carrier with a seal.
Who is responsible for a wrong piece count on an SLC load?
The shipper stated the count, so the shipper usually carries the burden of proving the quantity it says it loaded. The carrier remains responsible for damage or loss that happens after pickup.
Where should the SLC notation go?
It belongs on the bill of lading itself, in the description or remarks area, before the driver signs. A verbal agreement at the dock is hard to prove later.



