Saturday, November 21, 2026Sat, Nov 21 Updated

Trucking and freight news for drivers, carriers and shippers.

CDL Air Brakes Test: How Air Brakes Work and the In-Cab Check

The CDL air brakes test has a knowledge exam on how air brakes work and an in-cab check of leaks, warnings and spring brakes. Here is what each part covers.

Close-up of a motorcycle tire being inflated using a portable air pump.
Photo: Srattha Nualsate / Pexels

The CDL air brakes test has two parts: a written knowledge test on how air brake systems work, and an in-cab air brake check you perform during the vehicle inspection portion of the skills test. Passing both lets you drive a commercial vehicle with air brakes. Failing the knowledge test, or taking the skills test in a vehicle without full air brakes, usually puts an air brake restriction on your license.

Most states use the air brake section of their CDL manual, which follows a national model, so the material is close to the same everywhere. Check your own state’s manual for exact question counts and passing scores.

How does a truck air brake system work?

A truck air brake system uses compressed air, stored in tanks, to push the brake shoes or pads against the drums or rotors. The main parts are:

  • The air compressor, driven by the engine, which pumps air into the storage tanks.
  • The governor, which tells the compressor when to stop pumping (cut-out) and when to start again (cut-in).
  • Storage tanks, which hold enough air for several brake applications if the compressor fails.
  • Tank drains, used to remove water and oil that collect in the tanks.
  • An air dryer on most trucks, which removes moisture before it reaches the tanks.
  • The foot valve (brake pedal), which sends air to the brakes when you press it.
  • Brake chambers, pushrods and slack adjusters, which turn air pressure into force at each wheel.
  • Pressure gauges and a low-air warning (a light, a buzzer or both).

Most heavy trucks use S-cam drum brakes. Air enters the brake chamber, pushes the pushrod out, and the pushrod rotates the slack adjuster and the S-cam, which forces the shoes against the drum.

What is a dual air brake system?

A dual air brake system has two separate air systems, a primary and a secondary, that share one set of controls. One usually works the rear axle brakes and the other works the front axle brakes. If one system loses air, the other can still stop the truck, though with less braking power. Each system has its own gauge or a needle on a shared gauge, and the knowledge test expects you to know that you should not drive until both are at normal pressure.

How do spring brakes and parking brakes work?

Spring brakes are held off by air pressure and applied by powerful springs when that pressure is released or lost. The parking brake control (usually a yellow diamond-shaped knob) lets air out of the spring brake chambers so the springs apply. If air pressure leaks away in a serious failure, the spring brakes come on by themselves, which is why the test asks at what pressure range that happens. Combination vehicles also have a trailer air supply control (usually a red eight-sided knob) that protects the tractor’s air if the trailer line breaks.

Spring brakes only work as well as the brake adjustment allows. Brakes that are out of adjustment will hold poorly as parking brakes and stop poorly in an emergency.

What does the air brakes knowledge test cover?

The air brakes knowledge test covers the parts of the system, how they work together, how to inspect them and how to brake safely. Expect questions on:

  • What the governor, compressor, air dryer and safety relief valve do.
  • Why tanks must be drained and what happens if water freezes in the lines.
  • When the low-air warning must come on and what to do when it does.
  • When spring brakes apply on their own.
  • Brake lag: the short delay while air travels through the lines, which adds distance to every stop.
  • Checking slack adjusters for too much travel.
  • Brake fade on long grades and the right way to use the brakes going downhill.
  • What front-wheel limiting valves and modern anti-lock brakes (ABS) do.

Downhill braking questions come up often. Manuals teach choosing a low gear before the grade and using steady, light applications (snub braking) instead of riding the brakes. Engine retarders help on grades too, and our explainer on how engine brakes work covers that side, while the guide to downgrade gears and brake fade goes deeper on mountain driving.

What is the in-cab air brake check on the skills test?

The in-cab air brake check is a sequence of tests you perform and explain to the examiner while sitting in the driver’s seat. The usual steps in the model CDL manual are:

  1. Leak test with the brakes released: with the system fully charged and the engine off, release the parking brake, let the pressure settle and watch the gauge for one minute. The pressure loss must stay under the limit in your manual, which is lower for a single vehicle than for a combination.
  2. Leak test with the brakes applied: hold the brake pedal down firmly, let the pressure settle and watch for one minute. The allowed loss is slightly higher than in the released test.
  3. Low-air warning test: with the key on and the engine off, pump the brake pedal to drain air. The warning light and buzzer must come on before pressure drops below the level stated in the manual.
  4. Spring brake test: keep pumping. The parking brake knob should pop out (on most trucks) as pressure falls into the spring brake range, which shows the spring brakes have applied.
  5. Air pressure build-up test: start the engine, run it at a fast idle and time how long the pressure takes to climb through the range in the manual. Slow build-up points to a worn compressor or a leak.
  6. Governor cut-out and cut-in: let pressure build until the compressor stops, then fan the pedal until it starts again. Both points must fall within the manual’s ranges.
  7. Parking brake and service brake tests: tug gently against the parking brake in low gear, then make a slow stop with the service brake to check that the truck stops and does not pull to one side.

Examiners grade what you say as well as what you do. State each step, the number you are watching for and the result. Missing a step in the air brake check is a common reason applicants fail the inspection portion of the test.

How do you prepare for the air brakes test?

Read the air brakes section of your state’s CDL manual, then take practice tests until you can explain each part without notes. Since Feb. 7, 2022, first-time Class A and Class B applicants must finish entry-level training before the skills test, and air brakes are part of that theory curriculum; our page on who needs entry-level driver training explains the rules. For the order of permit, training and skills test, see the steps in how to get a CDL.

Practice the in-cab check out loud in the truck you will test in. Gauge layout, knob shapes and warning lights differ between models, and the examiner expects you to point to each one. The federal rules behind the CDL tests are published by the Federal Motor Carrier Safety Administration.

Quick answers

What happens if I fail the air brakes knowledge test?

In most states you can still get a CDL, but it carries an air brake restriction that bars you from driving vehicles with full air brakes. You can retake the test later to remove it.

Do I need the air brakes test for a Class C CDL?

You need it only if you will drive a Class C vehicle with air brakes, such as some buses. Without it, the air brake restriction applies.

Why do drivers drain air tanks?

Compressed air carries water and compressor oil that collect in the tanks. Water can freeze in cold weather and block valves or lines, so tanks without automatic drains are drained at the end of each day.

Is brake lag on the test?

Yes. Air brakes take a moment to apply after you press the pedal, so total stopping distance includes perception, reaction, brake lag and braking distance.